Customer project 121 - stars in wall above stairs


Thanks are due to Sara Lee for her very comprehensive details about her interesting project which involved fitting fibre optic stars to the wall above a staircase.


As part of a refurbishment project a new wall was being built at the top of a staircase and Sara hit on the idea of fitting fibres to the stud wall during the course of its construction. Since there'd be easy access behind the plasterboard while the stud wall was being built, this provided an excellent opportunity to permanently seal the fibres in place. There's no heat or electricity in the fibres and once fitted they'll be good for decades of service.


Positions for drilling are marked out before fitting the optical fibres.

First step, once the face of the new stud wall was in place, but before the plaster skim was applied,
was to mark out some star positions so as to get an idea of what sort of star distribution would work best.
The holes were drilled from the front after plastering and painting.

The optical fibre bundles are passed through holes drilled in the studwork.

On the rear side of the wall: the light source is fixed to one of the studs and the optical fibres gathered
into bundles to head off to their respective areas of the wall.

The optical fibres are divided into smaller bundles as they are distributed across the back of the wall.

Each of the bays between the studs has around 35 fibres. Holes were drilled in the studs and
noggins to pass the fibres through from one bay to another. Once the fibres were all in place the wall
would be sealed with a second layer of plasterboard and form the inside of a storage area.
The low-tack tape is used to manage the fibre

With the light source turned on, the fibres reflect nicely from the foil facing on the inner surface of the plasterboard.

The foil-faced inside of the plasterboard reflects the light from the fibres quite nicely.

Stars in place and illuminated.

The first stars in place. You can see two colours because the colour wheel is fitted to the light source
and as it rotates some stars change colour before others. The bits of tape on the wall are a reminder
of the location of the studs and noggins.

The finished display of fibre optic stars.

The finished project seen from the bottom of the stairs. With white selected the level of illumination
is reasonably high.

"This installation took 1.5 days with 2 people doing it," said Sara. "Because I was doing a wall, one of us drilled the holes and the other sat the other side of the wall poking the fibres through. We did not find the silicone satisfactory to hold the fibres in place – and used superglue in the end. If we were doing a ceiling then it would be highly unlikely that anyone would touch or knock your fibres. However for me, mine can be touched and I therefore needed to make sure they were very securely in place – given that I would never to be able to access the other side of the wall again.

"Dealing with 6 metres of fibres was a little tricky and my advice would be: Keep them in the sleeves they arrive in and think about how you’re going to install them before letting them loose! Rather than whipping the sleeves they arrive in off in one go, remove them about 30/40 centimetres at a time and tape the fibres with low tack tape, and continue until you get to the end. This really helps keep them under control – otherwise you’ll end up with a great big spaghetti mess. We switched the lightbox on and watched which fibres changed colour first so that we got them one side of the wall. We had 10 sections on the wall and separated ours into 30ish for each section. They do get tangled quite easily – and we used low tack masking tape to bunch ours in sections. We also taped the very ends to protect them whilst pushing them through the studwork.

 The fibre optic stars are a dramatic feature and a useful source of light.

View from the landing at the top of the stairs.

”This project was great fun," concludes Sara, "and Peter from Starscape was very helpful when I rang for advice. If you’re thinking of installing a fibre project in your house then do! They are visually stunning. Spend some time thinking about how to install your project, and don’t expect that it will be done quickly. It does require some time and patience – but the best things come to those who wait. Dealing with 300 x 6 metre fibres was a little like dealing with a bunch of unruly toddlers at times, but patience paid off – and we all love the end result.”

Back to Projects


Orders under £30.00 are usually delivered by Royal Mail first class. Please allow up to 5 days for delivery.
Over £30.00 delivery is by next working day courier. For Saturday deliveries there's a £20.00 surcharge.

For our customers' complete peace of mind Starscape’s online credit card transactions are handled by HSBC bank. The shopping cart (Roman Cart) is verified by VeriSign, and should you wish to complete your purchase over the phone we have computer systems and card information handling procedures verified by Security Metrics.

Links to the latest projects:

Why not browse through some of our 100+ project pages for ideas and inspiration?

Bathroom fibre optic lighting

Project 91

Wildlife projects at Starscape:

Wildlife at Woodside

Often seen in the surrounding wood, these three deer ventured a lot closer.

Wildlife at Woodside.....Read more

Get in Touch

  • Phone:
    01289 332900
  • Email:
  • Address:

  • Woodside
    TD15 2SY
    United Kingdom